Rodless Zylinder
ZS
ZSS
STANDARD CYLINDER
With identical fitting length as existing cylinders without piston
0-stroke compatible
ZK
ZKS
SHORT CYLINDER
With extremely shortened fitting length 0-stroke up to %42 shorter
ZF
ZFF
ZFK
ZFU
ZFB
GUIDING CYLENDER
With external an adjustable slide guide
For high Loads
ZP PARALLEL CYLINDER
for high loads and moments in every direction
double action force
central port
ZGS
ZGK
ZGF
ZGFK
GRIPPING CYLINDER
Gripping and clamping functions
Opening & closing functions
ZTS
ZTK
ZTF
TANDEM CYLINDER
For high moments in longitudinal direction
ZDS
ZDK
ZDF
ZDFK
DOUBLE ACTION CYLINDER
Double action force pressing, embossing, punching etc.
FB
MB
PB
KT
ACCESSORIES
Mounting brackets
Middle support
Swinging bridge
Cross support etc.
SAFETY REGULATIONS
The LANAMATIC cylinder is safe and made according to the latest technical research.
There could be a danger if
The cylinder will be used, mounted and maintained either improperly or by unqualified staff
The cylinder will not be used according to the regulations
The accident prevention regulations (UVV, VDE), the safety and installation regulations will not be respected
Working methods,restricting the function adn operation safety of the cylinder, have to be omitted.
The cylinder is exclusivelyto be used in the scope of its technical data; any other use beyond this is out of the regulations.
The manufacturer is not liable for damages caused by such an improper use.
In case of mounting, rebuilding or maintaning the energy supply has to be removed.
In case of maintenance, extension or rebuilding it is advisable to remove the cylinder from the working area and to do the work out of the danger zone.
When mounting, connecting, adjusting, bringing into service and testing the units it should be guarenteed that no mechanic or another person could operate the cylinders by mistake.
Additional bores, thread of attachments, being not offered as accessories, can only be applied after consulting the LANAMATIC AG.
Should a cylinder be operated in the neighbourhood of abrasive dust or aggressive vapour, the prior approval of LANAMATIC AG is necessary.
.Otherwise, the safety and accident preventation regulations of the operation place are valid.
NOTES
These data are to be used as product information and not as granted properties by law.
Any claim for damages againts us is to be ruled out, without considering the cause in law, unless intention or gross negligence could be applied to us.
All rights reserved for technical changes, omissions and fallacy
 
MOUNTING INSTRUCTION
  :Lubricate piston seals and cushioning ring lightly
Mount piston seals on piston
Put cushioning ring into the slot.
Take care that the smaller Ø of the ring is outside.
  :Lubricate sealing strip lightly.
Bend up one end and insert it into yoke.
Insert long end of sealing strip into the tube profile and put the yoke into the tube profile
  :Endcap is preassembled with strip cover and cushioning pin.
Lubricate o-ring and mount it.
  :Push yoke to the end and insert end cap.
On one side port insert flat sealing and tighten the special screws.
  :Insert cover strip and clamp it with grub screw.
Pull through yoke.
Measure exact length and clamp it on other side.
  :Pull the sealing strip tight (approx. 0.5 - 1 % of the length), stretch it and fix with grub screw with pin
Cut off overstanding sealing strip Insert wiper, screw on head wiper and tighten cover strip with it.
  :Fit grub screw with adhesive (Loctite)
Slide on guide carriage and adjust guiding bar with grub screws lightly
Beat guide carriage lightly with a rubber hammer from the side.
Check clearance, readjust if necessary
Technical Information
Construction Rodless cylinder with direct power transmission through the tube slot onto the yoke
Stroke Variable up to 6000mm, higher on request
Fitting Position Variable
Operation Double acting with adjustable end-of-travel cushioning
Operating Pressure 2 ... 8bar
Operating Temparature -20° C ... +80° C
Medium Filtered and slightly oiled or not lubricated compressed air
Material Aluminum parts made of highstrength alloy sealing parts made of oil resistant plastics and elastomers
  Weight
Cylinder Force/6 bar Cushioning ZS ZF ZFF Weight/Stroke
18 140 N 15 mm 0.3 kg 0.4 kg 0.6 kg 1.5 kg/1000 m
25 270 N 18 mm 0.6 kg 0.9 kg 1.1 kg 2.6 kg/1000 m
32 440 N 24 mm 1.1 kg 1.5 kg 2.2 kg 3.6 kg/1000 m
40 680 N 34 mm 1.8 kg 2.8 kg 3.8 kg 4.8 kg/1000 m
50 1060 N 40 mm 3.2 kg 4.9 kg 6.4 kg 7.4 kg/1000 m
63 1680 N 49 mm 5.6 kg 8.0 kg 10.4 kg 10.0 kg/1000 m
 
 
LOADS
All data concerning forces and torques refer to a speed of v<0.35m/s.
Observation keeping the indicated values ensures maximum service life, minimum noise and optimum operating results.
Higher speeds reduce the admissible forces

ZS Standard Cylinder

Cylinder V max <= 0.35 m/s V or port F Torques
Fx(N) Fy(N) Fz(N) F kab.
0.75 m/s
F kab.
1 m/s
F kab.
1.5 m/s
Mx(Nm)
Fy/ Fz
My(Nm)
Fx/Fz
Mz(Nm)
Fx/Fy
18 140 80 300 80 40 20 1 3 3
25 270 110 480 155 90 40 2 13 13
32 440 165 650 280 155 70 3.5 25 25
40 680 225 800 500 290 125 5.5 40 40
50 1060 325 1060 790 420 195 10 65 65
63 1680 435 1680 1500 850 370 16 100 100

ZF Guiding Cylinder

Cylinder V max <= 0.35 m/s V or port F Torques
Fx(N) Fy(N) Fz(N) F kab.
0.75 m/s
F kab.
1 m/s
F kab.
1.5 m/s
Mx(Nm)
Fy/ Fz
My(Nm)
Fx/Fz
Mz(Nm)
Fx/Fy
18 140 370 370 100 58 26 3.5 6 6
25 270 800 800 280 160 65 10 20 20
32 440 1200 1200 510 300 140 25 45 45
40 680 1600 1600 1000 550 250 40 75 75
50 1060 2100 2100 1500 850 380 80 150 150
63 1680 2800 2800 2500 1400 610 110 250 250
 
 



ZFF Double Guiding Cylinder

Cylinder V max <= 0.35 m/s V or port F Torques
Fx(N) Fy(N) Fz(N) F kab.
0.75 m/s
F kab.
1 m/s
F kab.
1.5 m/s
Mx(Nm)
Fy/ Fz
My(Nm)
Fx/Fz
Mz(Nm)
Fx/Fy
18 140 550 550 150 80 31 5.2 9 9
25 270 1200 1200 420 210 80 15 30 30
32 440 1800 1800 750 400 170 37 67 67
40 680 2400 2400 1500 750 300 60 110 110
50 1060 3200 3200 2200 1150 460 120 220 220
63 1680 4200 4200 3700 1900 740 170 370 370
 
 
Pos
DESCRIPTION MATERIAL
1
Tube Al Mg Si 0.5 Anodized
2
Rond Profile TPU
3
Sealing Strip PA
4
Cover Strip Stainless Steel
5
Yoke Al Anodized / POM
6
Endcap Al Anodized
7
Special Screw Zinc-Plated Steel
8
Cushioning Pin Stainleess Steel
9
Strip Cover POM
10
Head Wiper POM
11
Wiper POM
12
Carriage Al Anodized
13
Cone Nut Zinc-Plated Steel
14
Clamp Wedge Al Anodized
15
Guiding Bar POM
16
Press Bar Stainleess Steel
17
Piston Seal PU
18
Cushion Ring NBR
19
O-ring NBR
20
O-ring NBR
21
Flat Seat NBR
22
Countersunk Screw Zinc-Plated Steel
23
Grup Screw With Pin Zinc-Plated Steel
24
Cylinder Head Screw Zinc-Plated Steel
25
Plug Screw Zinc-Plated Steel
26
Grup Screw Steel
27
Grup Screw With Pin Steel
28
Plain Washer Zinc-Plated Steel
29
Cylinder Head Screw Zinc-Plated Steel
30
Grup Screw Steel
31
Square Nut Zinc-Plated Steel
ZS Standard Cylinder

ØA AF AM B C CA CB D DA DB DC DD E F G J M N ØO S T U W
Ø 18 80 50 10 16.5 6.5 - - M7x1/6 15.5 - - - 103 75 - 3 15.5 M3x6 Ø 3.5 23.5 M3x7 30 39
Ø 25 100 70 13 20 8.5 7 13 G1/8x8 25.5 14 28 18.5 131 100 50 3.5 20 M4x7 Ø 4.5 33 M4x9 42 53
Ø 32 120 100 16 20 8.5 7 13 G1/8x8 32 16 34.5 21 171 140 70 4.5 25 M5x9 Ø 5.5 41 M5x10 52 65
Ø 40 150 140 22 23 13 11 14.5 G1/4x12 37.5 18.5 41 29.5 220 180 90 5 33 M6x10 Ø 7 51 M6x12 63 79
Ø 50 180 180 29 23 13 12 14 G1/4x12 47.5 22.5 47.5 37 280 220 110 6.5 42 M8x12.5 Ø 7 63 M8x12 78 96
Ø 63 215 230 40 29 13 12.5 15.5 G3/8x12 59.5 24.5 59.5 44.5 333 280 140 8 54 M8x15 Ø9 78 M8x12 93 113.5
 
Example for order :
ZS Ø 25 Standart cylinder with stroke 100mm






Order number.
1 2 5 0 - 0 0 0 0 - 0 1 0 0 Port Standart
1 2 5 0 - 0 0 0 1 - 0 1 0 0 Port Underneath
1 2 5 0 - 0 0 0 2 - 0 1 0 0 One Side Port
 
 
ZF Guiding Cylinder

ØA AM B BM C CA CB D DA DB DC DD FE FF FG FM FW N S T U
Ø 18 80 10 16.5 35 6.5 - - M7x1/6 17.5 - - - 103 75 - 50 39 M4x7.5 23.5 M3x7 30
Ø 25 100 13 20 45 8.5 7 13 G1/8x8 25.5 14 28 18.5 131 100 50 66 53 M4x8 33 M4x9 42
Ø 32 120 16 20 55 8.5 7 13 G1/8x8 32 17.5 34.5 21 171 140 70 80 65 M5x10 41 M5x10 52
Ø 40 150 22 24 70 13 9.5 14.5 G1/4x12 37.5 20 42 29.5 220 180 90 97 79 M6x12 51 M6x12 63
Ø 50 180 29 24 85 13 9.5 14.5 G1/4x12 47.5 26 52 37 280 220 110 116 96 M8x16 63 M8x12 78
Ø 63 215 40 30 105 13 11 18.5 G3/8x12 59.5 30 62 44.5 333 280 140 136 113.5 M8x16 78 M8x12 93
 
Example for order :
ZF Ø 25 Guiding cylinder with stroke 100mm







Order number.
3 2 5 0 - 0 0 0 0 - 0 1 0 0 Port Standart
3 2 5 0 - 0 0 0 1 - 0 1 0 0 Port Underneath
3 2 5 0 - 0 0 0 2 - 0 1 0 0 One Side Port
 
 
ZFF Double Guiding Cylinder


Ø
A AM B BM C CA CB D DA DB DC DD FE FF FG FM FW N S T U
Ø 18 80 10 16.5 35 6.5 - - M7x1/6 17.5 - - - 103 75 - 50 48 M4x7.5 23.5 M3x7 30
Ø 25 100 13 20 45 8.5 7 13 G1/8x8 25.5 14 28 18.5 131 100 50 66 64 M4x8 33 M4x9 42
Ø 32 120 16 20 55 8.5 7 13 G1/8x8 32 17.5 34.5 21 171 140 70 80 78 M5x10 41 M5x10 52
Ø 40 150 22 24 70 13 9.5 14.5 G1/4x12 37.5 20 42 29.5 220 180 90 97 95 M6x12 51 M6x12 63
Ø 50 180 29 24 85 13 9.5 14.5 G1/4x12 47.5 26 52 37 280 220 110 116 114 M8x16 63 M8x12 78
Ø 63 215 40 30 105 13 11 18.5 G3/8x12 59.5 30 62 44.5 333 280 140 136 134 M8x16 78 M8x12 93
Example for order :
ZFF Ø 25 Guiding cylinder with stroke 100mm







Order Number
3 2 5 1 - 0 0 0 0 - 0 1 0 0 Port Standart
3 2 5 1 - 0 0 0 1 - 0 1 0 0 Port Underneath
3 2 5 1 - 0 0 0 2 - 0 1 0 0 One Side Port

FB Mounting brackets

Cylinder
Ø mm
AA AB AC AD AE AH Order Number
Ø 18 15 2 10 20 Ø 6 2 1182-0001
Ø 25 18 2 12.5 30 Ø 6 2 1252-0001
Ø 32 20 2.5 13.5 40 Ø 7 3 1322-0001
Ø 40 30 3 17.5 50 Ø 9 3.5 1402-0001
Ø 50 28 3 20 60 Ø 9 3 1502-0001
Ø 63 30 3 21 75 Ø 11 4.5 1632-0001

The order No. given includes 2 mounting brackets and 8 screws.

MB Middle Support

Cylinder Ø mm AE AH BA BB BC BD BE BF Order Number
Ø 18 Ø 6 2 56 46 36.5 23 2.5 8.25 1183-0001
Ø 25 Ø 6 2 70 60 50 28 3.5 11 1253-0001
Ø 32 Ø 7 3 85 73 61.5 33 4 13.8 1323-0001
Ø 40 Ø 9 3 105 90 75 38 4.5 16 1403-0001
Ø 50 Ø 9 3 122 106 91 43 5 19 1503-0001
Ø 63 Ø 11 4.5 144 125 107 48 6 22 1633-0001
The order No. given includes 2 mounting brackets and 4 screws.
 
 
Deflection Diagram
MB middle support
When using very long cylinders or applying heavy loads, the tube deflection is to be taken into consideration. One or more middle supports are to be used according to the admissible deflection.
Example:
A cylinder Ø 25 should deflect by a maximum of 0.5 mm when applying a force FZ of 500N. According to the diagram the cylinder can be 750 mm long. Longer cylinders must have a middle support.
Other possibilities
In case very long cylinders are installed without supports, an additional profile can be used as a support.
Examples:
All versions with middle support and standart profiles.


 
 

AS Stop Adjustment

Cylinder Ø mm A
ZF/ZFK
AH B
ZF/ZFK
C D E F G H M N O SW T
Ø 18 80/57.5 2 113/90.5 32 Max. 25 57 43.5 8 23.5 M10x1 8 15 13 M3x10
Ø 25 100/67.5 2 117.5/85 37 Max. 40 72 57 12.5 33 M14x1.5 10 20 17 M4x10
Ø 32 120/77.5 3 135.5/90 70 Max. 30 84 70 14.5 41 M14x1.5 12 20 17 M5x12
Ø 40 150/95 3 165/110 65 Max. 50 105 93 16 51 M25x1.5 15 30 32 M6x15
Ø 50 180/105 3 195/140 80 Max. 65 126 102 22.5 63 M25x1.5 15 30 32 M8x20
Ø 63 215/125 4.5 250/160 80 65 140 118.5 20 78 M25x1.5 15 40 32 M8x20


Example for Order : AS25 stop adjustment shiftable gor ZF25 or ZFK25 (without shock absorbers)

Order Number.
1 2 5 8 - 0 0 0 0

  Cylinders
3D IGES
Click on the buttons to download the file format drawings.  >  
Cylinders ZS ZF ZFF
0 Stroke
Ø 25
Ø 32
Ø 40
Ø 50
Cylinders ZS ZF ZFF
0 Stroke
Ø 25
Ø 32
Ø 40
Ø 50
Cylinders ZS ZF ZFF
0 Stroke
Ø 25
Ø 32
Ø 40
Ø 50
  Baðlantý Parçalarý
Ø 25
(AB) Ayak Baðlantý
(OB) Orta Baðlantý
Ø 32
(AB) Ayak Baðlantý
(OB) Orta Baðlantý
Ø 40
(AB) Ayak Baðlantý
(OB) Orta Baðlantý
Ø 50
(AB) Ayak Baðlantý
(OB) Orta Baðlantý
  Mounting Parts
Ø 25
(FM) Foot Mounting
(CM) Central Mounting
Ø 32
(FM) Foot Mounting
(CM) Central Mounting
Ø 40
(FM) Foot Mounting
(CM) Central Mounting
Ø 50
(FM) Foot Mounting
(CM) Central Mounting